HomeEnvironmentalPower Analysers › Cropico DO6 Digital Ohmmeter


Cropico DO6 Digital Ohmmeter


A COMPREHENSIVE DIGITAL OHMMETER WITH TEMPERATURE COMPENSATION


Covering a wide range of measurements from 1 micro ohm to 200 kilo ohm, the DO6 is a comprehensive measuring instrument with many features incorporated as standard.

These benefits include manual and automatic range selection; temperature compensation for copper, referencing the measurement of copper to 20°C; voltage limiting facility for those wishing to measure switch contact resistance to International Standards, the measurement voltage is limited to 20mV.

An RS232 serial interface gives full talk / listen capability, making it simple to add to an automated measuring system. Hi / Lo limits may be set over the interface with voltage-free contacts being available on the rear panel.

For those wishing to measure inductive circuits e.g. motor windings, a special protection circuit may be initiated thus avoiding any problems that may arise due to induced high voltage.


Data Sheet

Key Features

  True 4 wire measurement eliminates lead resistance errors
  8 push button ranges 20 milli ohm… 200 kilo ohm
  Resolution of 1 micro ohm on 20 milli ohm range
  Manual / automatic range selection
  Temperature compensation for copper and brass
  Thermal E.M.F. compensation
  Dry circuit measurement: 18mV limited
  Open circuit lead warning
  RS232 interface
  Hi / Lo limits

Specifications


Measurement

4 Terminal Kelvin/Thomson, eliminating lead resistance errors

Display

4.5 digit 15mm 7 segment LED with polarity and overload indication. 2 digit 16 segment LED for unit display

Ranges

8 ranges manual selection with up/down keys, automatic selection with autorange function

Auto Zero

Permits the automatic zero of amplifiers and external circuits

Temperature Compensation

Measurement compensated for the following referenced to 20°C: Copper Cu = 3.93%/K Brass Ms63 = 1.50%/K Brass Ms80 = 1.60%/K Ambient sensed with Pt 100 sensor

Relay Output

For the pre-selected upper and lower limit values "Too small", "Correct", "Too large" Contact load = 30W max 48V 1 Amp

Dry Circuit Measurement

In accordance with DIN 41640 part 4 and IEC - 132-1 Open circuit voltage limited to 18mV

Interface

RS232 25 pin D-Bush talk listen function

Terminals

4mm safety sockets

Working Temperature

0°C to 50°C rel. humidity 90% max. non-condensing

Storage Temperature

-20°C to +60°C

Mains Supply

230 Volts +6% - 10% 45Hz to 65Hz approx. 30VA

Safety

IEC 1010 Protective Class 1

Dimensions

255mm x 90mm x 263mm (W D H) approx

Mass

5kg approximately

Please note - Product designs and specifications are subject to change without notice. The user is responsible for determining the suitability of this product.

Back To Last Page


Cropico

Digital Ohmmeters

DO4A Portable Ohmmeter
DO6 Digital Ohmmeter
DO5000 Series Ohmmeters

Handheld Micro Ohmmeters

DO4000 & DO4001 Micro Ohmmeters
DO4002 Micro Ohmmeter

Portable Micro Ohmmeters

DO7 Micro Ohmmeter
DO7e Micro Ohmmeter
DO7 Plus Micro Ohmmeter
DO7010 Digital Microhmmeter

Resistance Standards & Decades

00Series Decade Boxes
CM5-N Capacitance Compensation Box
CR Calibrator Resistor
MTS Milliohmmeter
RBB Decade Resistance Box
RBC Decade Resistance Box
RH9A Decade Resistance Box
RM6 Decade Resistance Box
RM6N Decade Resistance Box
RM8 Decade Resistance Box
RS3 Resistance Standard

Temperature Measurement

Series 3000 Digital Thermometer

Want A Quotation?

Please fill out the following fields and we will e-mail you a quotation shortly.